Certified product 
SAFETRON 6600HD is certified according to the Swedish Anti-Theft Association's standard SSF 3522 class 2A, 2B, 3, 4 and 5 and the European standard SS-EN 14846 Grade 7. SAFETRON 6600HD is also approved as a lock in doors with class RC3 and RC4 with the market's leading door manufacturers.
Fire doors
SAFETRON 6600HD is equipped with a reinforced hook bolt piston and a drop piston for pressure function and restraining properties in e.g. fire doors. Motor lock 6600HD is advantageously used as the only lock in doors with protection class requirements 1, 2 or 3. SAFETRON 6600HD is approved in fire class E/EI120.
Modern falleplassering
SAFETRON 6600HD has falleplassering modern falleplassering means that the lock is adapted for modern doors from the leading door manufacturers in Scandinavia.
SAFETRON 6600HD
IP rated motor lock for harsh environments and critical infrastructure
The SAFETRON 6600HD is a revolution in high security locking in harsh environments. The lock housing is based on the proven 6600 motor lock but is enclosed and is protected against water, moisture and dust thanks to its IP67-rated electronics. The control unit is also supplied in an IP66-rated enclosure.
The motor lock protects people and property in commercial properties and critical infrastructure where it is used to lock doors with high security requirements. Installed in a certified RC-classified door, the 6600HD is approved for security requirements:
- Protection class 1
- Protection class 2
- Protection class 3
Typical locations where HD Series motor locks are used are tunnels, bridges, mines, coastal sites and other extreme environments where high security requirements exist.
The 6600HD motor lock disengages in less than 0.1 seconds, therefore a separate day lock is not normally required on high-frequency doors.
-
Certified SSF 3522
-
IP class: 67
-
EX class: Pending
-
Lock class 5
-
Fire rating E/EI 120
-
Assessed by Byggvarubedömningen
-
5-year warranty
Order from one of our distributors
Customer accounts are required with all distributors.
IP rated enclosure
The CU2 controller is supplied in an IP rated enclosure (IP 66) making installation in harsh environments possible even for the controller.
Integrated with access control systems
The SAFETRON 6000 series offers integrated control for several of the market's major access control system suppliers via OSDP®.
This means that the motor locks can be connected directly to the access control system's door controller without styreenhet then configured using the access control system's software, which simplifies installation and provides a more cost-effective door environment.
Axema VAKA |
|
NOX access system |
|
Parakey Slim |
|
Sentrion |
|
Tidomat Smartone |
|
Techsolutions Techpoint |
|
AXIS1 |
|
RCO1 |
|
Vanderbilt Omnis1 |
1 Under development
Connection via styreenhet
Connection via styreenhet using SAFETRON CU2, which is supplied in all kit packages. The CU2 control unit has the widest range of applications on the market in a single styreenhet. Two motor locks can be connected without any restrictions on signal exchange, which means that the CU2 is effectively two control units in one. The CU2 also offers the option of programming AUX relays for the desired function.
Emergency exit according to SS-EN 179
SAFETRON 6600HD can be used in emergency escape routes together with SAFETRON emergency escape accessory 796 according to the European standard SS-EN 179:2008, and SSF 3522 class 2B. The combination provides a door environment where requirements for both high security and emergency evacuation are met in one locking unit.
Re-entry
SAFETRON 6600HD together with 796 offers the possibility of tilbakerømning. In an emergency evacuation situation, the motor lock is opened via the emergency evacuation device, and the built-in microswitch in the emergency evacuation device signals to the control unit that an emergency opening has taken place. If tilbakerømning in the control unit, the motor lock is placed in an unlocked position until manual reset via a signal to the control unit occurs, which then locks the motor lock. tilbakerømning reset are handled in the control unit and can therefore be administered by a higher-level system.
| Description | Surface treatment | nickel free |
|---|---|---|
| SAFETRON 796 H | Chrome, Matt chrome, Matt black | |
| SAFETRON 796 V | Chrome, Matt chrome, Matt black |
Developed and manufactured in Sweden
SAFETRON 6600HD, like all our motor locks, is developed and manufactured in Sweden for the Scandinavian market. Our locks are made of materials that can withstand tough environments and security requirements. We do not cut corners where others do, but guarantee high-quality products even if it means a more expensive manufacturing process.
Hardox
Essential parts are produced in Hardox® steel from SSAB, a steel with unique properties in terms of wear resistance, hardness and toughness. Why manufacture products with materials from other countries when we are the best in the world at home?
Few moving parts
The 6000 series motorized locks are based on a design philosophy with few moving parts. Having developed and produced motorized locks for over 30 years, we know what it takes to make powerful, durable and reliable motorized locks that work in real-life door environments.
